User Tools

Site Tools


wphase:documentation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
wphase:documentation [2018/05/03 16:54]
wphase [RUNA scripts]
wphase:documentation [2018/05/03 16:57] (current)
wphase [RUNA scripts]
Line 123: Line 123:
 $WPHASE_HOME/​bin/​wpinversion -ifil o_wpinv.th1.3 -ofil o_wpinv.th0.9 -th 0.9  $WPHASE_HOME/​bin/​wpinversion -ifil o_wpinv.th1.3 -ofil o_wpinv.th0.9 -th 0.9 
 </​code>​ </​code>​
-  - Finally, it is possible to remove the channels showing a large rms ratios (observed/​predicted and predicted/​observed) using the option –nr (e.g. –nr 2.0): <​code>​+  - Finally, it is possible to remove the channels showing a large rms amplitude ​ratios (observed/​predicted and predicted/​observed) using the option –nr (e.g. –nr 2.0): <​code>​
 $WPHASE_HOME/​bin/​wpinversion -ifil o_wpinv.th0.9 -ofil o_wpinv.th1.3 -nr 2.0 $WPHASE_HOME/​bin/​wpinversion -ifil o_wpinv.th0.9 -ofil o_wpinv.th1.3 -nr 2.0
 </​code>​ </​code>​
Line 135: Line 135:
 ----- -----
 ==== RUNA scripts ==== ==== RUNA scripts ====
-Data extraction, screening and inversion described above can be performed by running one of the RUNA3*csh scripts (usually in bin). These scripts perform data extraction/​screening and calculate a moment tensor solution after median data screening and after rejecting ​ traces associated with large misfit using the threshold 5.0 3.0 0.9 (i.e. -th, see 2. in section ​4):+Data extraction, screening and inversion described above can be performed by running one of the RUNA3*csh scripts (usually in bin). These scripts perform data extraction/​screening and calculate a moment tensor solution after median data screening and after rejecting ​ traces associated with large misfit using the threshold 5.0 3.0 0.9 (i.e. -th, see 2. in the "​Inversion" ​section ​above):
 <​code>​ <​code>​
 ${WPHASE_HOME}/​bin/​RUNA3.csh ${WPHASE_HOME}/​bin/​RUNA3.csh
Line 145: Line 145:
 will perform median and rms misfit screening for Z channels only. will perform median and rms misfit screening for Z channels only.
  
-These two scripts don’t perform the “ratio screening” (i.e. 3. above). To run the same routines with an additional screening based on the amplitude ratio (observed/​predicted and predicted/​observed),​ the following script can be used:+These two scripts don’t perform the “ratio screening” (i.e. 3. in the "​Inversion"​ section ​above). To run the same routines with an additional screening based on the rms amplitude ratio (observed/​predicted and predicted/​observed),​ the following script can be used:
 <​code>​ <​code>​
 ${WPHASE_HOME}/​bin/​RUNA3r.csh ​ ${WPHASE_HOME}/​bin/​RUNA3r.csh ​
wphase/documentation.1525359268.txt.gz · Last modified: 2018/05/03 16:54 by wphase