wphase:documentation
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
wphase:documentation [2018/03/26 16:52] wphase [Building the code] |
wphase:documentation [2018/05/03 16:57] wphase [RUNA scripts] |
||
|---|---|---|---|
| Line 123: | Line 123: | ||
| $WPHASE_HOME/bin/wpinversion -ifil o_wpinv.th1.3 -ofil o_wpinv.th0.9 -th 0.9 | $WPHASE_HOME/bin/wpinversion -ifil o_wpinv.th1.3 -ofil o_wpinv.th0.9 -th 0.9 | ||
| </code> | </code> | ||
| - | - Finally, it is possible to remove the channels showing a large rms ratios (observed/predicted and predicted/observed) using the option –nr (e.g. –nr 2.0): <code> | + | - Finally, it is possible to remove the channels showing a large rms amplitude ratios (observed/predicted and predicted/observed) using the option –nr (e.g. –nr 2.0): <code> |
| $WPHASE_HOME/bin/wpinversion -ifil o_wpinv.th0.9 -ofil o_wpinv.th1.3 -nr 2.0 | $WPHASE_HOME/bin/wpinversion -ifil o_wpinv.th0.9 -ofil o_wpinv.th1.3 -nr 2.0 | ||
| </code> | </code> | ||
| Line 135: | Line 135: | ||
| ----- | ----- | ||
| ==== RUNA scripts ==== | ==== RUNA scripts ==== | ||
| - | Data extraction, screening and inversion described above can be performed by running one of the RUNA3*csh scripts (usually in bin). These scripts perform data extraction/screening and calculate a moment tensor solution after median data screening and after rejecting traces associated with large misfit using the threshold 5.0 3.0 0.9 (i.e. -th, see 2. in section 4): | + | Data extraction, screening and inversion described above can be performed by running one of the RUNA3*csh scripts (usually in bin). These scripts perform data extraction/screening and calculate a moment tensor solution after median data screening and after rejecting traces associated with large misfit using the threshold 5.0 3.0 0.9 (i.e. -th, see 2. in the "Inversion" section above): |
| <code> | <code> | ||
| ${WPHASE_HOME}/bin/RUNA3.csh | ${WPHASE_HOME}/bin/RUNA3.csh | ||
| Line 145: | Line 145: | ||
| will perform median and rms misfit screening for Z channels only. | will perform median and rms misfit screening for Z channels only. | ||
| - | These two scripts don’t perform the “ratio screening” (i.e. 3. above). To run the same routines with an additional screening based on the ratio (observed/predicted and predicted/observed), the following scripts can be used: | + | These two scripts don’t perform the “ratio screening” (i.e. 3. in the "Inversion" section above). To run the same routines with an additional screening based on the rms amplitude ratio (observed/predicted and predicted/observed), the following script can be used: |
| <code> | <code> | ||
| ${WPHASE_HOME}/bin/RUNA3r.csh | ${WPHASE_HOME}/bin/RUNA3r.csh | ||
wphase/documentation.txt · Last modified: 2022/01/10 07:39 by wphase
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
